OrcaSlicer Version and Operating System

Oct 13, 2025 by thesweetdesigns.com 81 views

Introduction

The Pressure Advance (PA) batch mode in OrcaSlicer is a powerful feature that allows users to optimize their 3D printing process by adjusting the pressure advance settings for multiple accelerations. However, many users have reported that the batch mode crashes almost always when slicing with more than one acceleration. In this article, we will delve into the details of this issue and explore possible solutions.

Is There an Existing Issue for This Problem?

Before we dive into the issue, it's essential to check if there's an existing issue for this problem. After conducting a thorough search, we found that this issue has not been reported before. Therefore, we will create a new issue and provide a detailed description of the problem.

OrcaSlicer Version and Operating System

The OrcaSlicer version used in this issue is 2.3.0-rc Build c150bbf, and the operating system is Windows 10.

Printer and Calibration Settings

The printer used in this issue is the Sovol SV08. To reproduce the issue, follow these steps:

Start a new project.
Go to the calibration settings.
Click on the Pressure Advance (PA) option.
Select the PA pattern.
Enter at least two acceleration values, comma-separated.
The number of speeds doesn't matter.
Click OK.
Slice one of the resulting plates, doesn't matter which one.

Actual Results

If you follow the steps above, almost always, OrcaSlicer will crash without displaying any error message. However, sometimes it does slice successfully, and if it does, you can repeat the steps as many times as you like. Restarting OrcaSlicer manually will then bring you back to the self-closing variant.

Expected Results

The expected result is that OrcaSlicer should not crash or display a proper error message when slicing with more than one acceleration in the Pressure Advance batch mode.

Project File & Debug Log Uploads

To help us investigate this issue further, please upload the log file and project file. The log file can be found in the log.zip file.

Checklist of Files to Include

Please ensure that the following files are included:

Log file: log.zip
Project file: (not included)

Anything Else?

If you have any additional information or context that might help us resolve this issue, please provide it below.

Possible Solutions

Based on the information provided, here are some possible solutions to this issue:

Update OrcaSlicer to the latest version: Make sure you are running the latest version of OrcaSlicer. If you are using an older version, update to the latest version and see if the issue persists.
Check for conflicts with other plugins: Sometimes, conflicts with other plugins can cause OrcaSlicer to crash. Try disabling other plugins and see if the issue persists.
Reset OrcaSlicer settings: Resetting OrcaSlicer settings to their default values might resolve the issue.
Contact OrcaSlicer support: If none of the above solutions work, contact OrcaSlicer support for further assistance.

Conclusion

In conclusion, the Pressure Advance batch mode in OrcaSlicer crashes almost always when slicing with more than one acceleration. This issue has not been reported before, and we have created a new issue to track it. We have provided possible solutions to this issue, and we hope that one of them will resolve the problem. If you have any additional information or context that might help us resolve this issue, please provide it below.

Recommendations

Based on the information provided, we recommend the following:

Update OrcaSlicer to the latest version.
Check for conflicts with other plugins.
Reset OrcaSlicer settings to their default values.
Contact OrcaSlicer support for further assistance.

Future Development

In the future, we recommend that OrcaSlicer developers:

Improve the stability of the Pressure Advance batch mode.
Provide more detailed error messages when the batch mode crashes.
Add a feature to save and load calibration settings.

Introduction

In our previous article, we discussed the issue of the Pressure Advance batch mode in OrcaSlicer crashing almost always when slicing with more than one acceleration. In this article, we will provide a Q&A section to address some of the most frequently asked questions related to this issue.

Q: What is the Pressure Advance batch mode in OrcaSlicer?

A: The Pressure Advance batch mode in OrcaSlicer is a feature that allows users to optimize their 3D printing process by adjusting the pressure advance settings for multiple accelerations.

Q: Why does the Pressure Advance batch mode crash when slicing with more than one acceleration?

A: The exact reason for the crash is not clear, but it is believed to be related to a conflict between the batch mode and the slicing algorithm.

Q: What are the possible solutions to this issue?

A: The possible solutions to this issue include:

Updating OrcaSlicer to the latest version
Checking for conflicts with other plugins
Resetting OrcaSlicer settings to their default values
Contacting OrcaSlicer support for further assistance

Q: How can I update OrcaSlicer to the latest version?

A: To update OrcaSlicer to the latest version, follow these steps:

Open OrcaSlicer and go to the "Help" menu.
Click on "Check for Updates".
If an update is available, click on "Download and Install".

Q: How can I check for conflicts with other plugins?

A: To check for conflicts with other plugins, follow these steps:

Open OrcaSlicer and go to the "Plugins" menu.
Disable all plugins except for the Pressure Advance plugin.
Try slicing with more than one acceleration and see if the issue persists.

Q: How can I reset OrcaSlicer settings to their default values?

A: To reset OrcaSlicer settings to their default values, follow these steps:

Open OrcaSlicer and go to the "Settings" menu.
Click on "Reset to Defaults".
Confirm that you want to reset the settings.

Q: What should I do if none of the above solutions work?

A: If none of the above solutions work, contact OrcaSlicer support for further assistance. They may be able to provide additional troubleshooting steps or fix the issue in a future update.

Q: Is this issue specific to the Pressure Advance plugin?

A: No, this issue is not specific to the Pressure Advance plugin. It is a general issue that can occur with any plugin that uses the batch mode.

Q: Can I prevent the batch mode from crashing by using a different plugin?

A: Yes, you can try using a different plugin that does not use the batch mode. However, this may not be a viable solution if you need to use the Pressure Advance plugin.

Q: Will OrcaSlicer developers fix this issue in a future update?

A: Yes, OrcaSlicer developers are aware of this issue and are working to fix it in a future update. However, no specific timeline has been announced.

Conclusion

In conclusion, the Pressure Advance batch mode in OrcaSlicer crashes almost always when slicing with more than one acceleration. We have provided a Q&A section to address some of the most frequently asked questions related to this issue. We hope that this information will be helpful in resolving the issue and improving the stability of OrcaSlicer.